Aka-Cut 500 HV 254 mm.png
Aka-Cut Fe50 250 mm.png
Aka-Cut Fe60 250 mm.png
Aka-Cut NF10 250 mm.png
Aka-Cut Ti20 250 mm.png
Aka-Cut 500 HV 305 mm.png
Aka-Cut Fe50 300 mm.png
Aka-Cut Fe60 300 mm.png
Aka-Cut NF10 300 mm.png
Aka-Cut Ti20 300 mm.png
Aka-Cut 500 HV 350 mm.png
Aka-Cut Fe50 350 mm.png
Aka-Cut Fe60 400 mm.png
Aka-Cut Fe60 350 mm.png
Aka-Cut 500 HV 406 mm.png
Aka-Cut Fe50 400 mm.png
Aka-Cut Fe50 432 mm.png
Aka-Cut Fe60 432 mm.png
Aka-Cut Ti20 350 mm.png
Aka-Cut 500 HV 254 mm.png
Aka-Cut Fe50 250 mm.png
Aka-Cut Fe60 250 mm.png
Aka-Cut NF10 250 mm.png
Aka-Cut Ti20 250 mm.png
Aka-Cut 500 HV 305 mm.png
Aka-Cut Fe50 300 mm.png
Aka-Cut Fe60 300 mm.png
Aka-Cut NF10 300 mm.png
Aka-Cut Ti20 300 mm.png
Aka-Cut 500 HV 350 mm.png
Aka-Cut Fe50 350 mm.png
Aka-Cut Fe60 400 mm.png
Aka-Cut Fe60 350 mm.png
Aka-Cut 500 HV 406 mm.png
Aka-Cut Fe50 400 mm.png
Aka-Cut Fe50 432 mm.png
Aka-Cut Fe60 432 mm.png
Aka-Cut Ti20 350 mm.png

Aka-Cut Abrasive Cut-Off Wheels

from £153.00

Supplied in boxes of 10 except 432mm which are supplied in boxes of 5

Size:
Type:
Quantity:
Add To Cart

Supplied in boxes of 10 except 432mm which are supplied in boxes of 5

Supplied in boxes of 10 except 432mm which are supplied in boxes of 5

Metallographic cutting is the first and very important step in sample preparation. To take out a representative sample from a large workpiece or to make longitudinal or cross sections of smaller parts, it must be ensured that the sample is removed without the creation of heat that could modify or even damage the structure. The surface of the sample after cutting must be free from thermal damage and with a minimum of mechanical deformation. Otherwise the following preparation steps will take very long time, and there is a risk that possible changes to the microstructure are not removed and may be seen as the “real” structure. Our wheels are, in respect of the above, optimised especially for metallographic cutting to provide perfect results in the shortest possible time. The abrasive cut-off wheels for laboratory and production type cut-off machines are available in 5 different standard sizes, from 250 to 432 mm dia., with an arbor size of 32 mm dia. Our precision cut-off wheels are optimised for high precision cutting of different materials. They are as thin as possible in relation to the diameter to remove an absolute minimum of material, a critical factor when sectioning expensive materials. Thin cut-off wheels limit the thermal damage and mechanical deformation during cutting. This again reduces the following grinding and polishing time.

Our range of cut-off wheels are named with both the material group they are designed for and the approximate hardness range. As can be seen in the table below, there are two Fe wheels for Ferrous Metals with a hardness of approximately 60 and 50 HRC. The third wheel is especially developed for Titanium and Titanium Alloys, and the fourth wheel is designed for other, soft Non-Ferrous Metals. Aka-Cut 500 HV is a fibre-reinforced wheel, well suited for cutting of surface hardened workpieces. The fibre-reinforcement strengthens the wheel and reduces breaking when subjected to pinching. Use the table below to select the correct wheel for your specific material type, hardness and size. Additionally we also have a selection of precision cut-off wheels in 150 mm dia.

Cut Off Wheel Selection Chart

Wheel Sizes are:

Aka-Cut 500HV 254 x 1.7 x 32mm, 305 x 2.2 x 32mm, 354 x 2.6 x 32mm, 406 x 3.2 x 32mm

Fe50, Fe60, NF10 & Ti20 250 x 1.5 x32mm, 300 x 2.0 x 32mm, 350 x 2.5 x 32mm, 400 x 3.0 x 32mm, 432 x 3.0 x 32mm